swissporBIKUPLAN V 3.0
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references.
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie www.rilco.ie
swissporBIKUPLAN V 3.0
BIKUPLAN V 3.0 are high quality SBS modi ed membranes reinforced with a berglass eece. The berglass re- inforcement grants a very good dimensional stability of the product. The upper face of swissporBIKUPLAN V 3.0 is a polypropylene eece that prevents the membrane from being damaged by walking during the application process in the hot days. This upper nish render the membrane compatible with the usage of different types of glues and different types of waterproo ng paints.
These membrane is generally used as vapour barrier and, in some cases, as under layer in multiple layers water- proo ng solution. It shall be applied fully bonded with a suitable propane torch.
swissporBIKUPLAN V 3.0 ff
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references.
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie
www.rilco.ie
TECHNICAL DATA SHEET swissporBIKUPLAN V 3.0 ff
swissporBIKUPLAN V 3.0 are high quality SBS modi ed membranes reinforced with a berglass eece. The berglass reinforcement grants a very good dimensional stability of the product. The swissporBIKUPLAN V 3.0 ff is nished in the upper part with a lm that is easily torchable. The lower face of these membranes is nished with a high quality polypropylene lm that permits a very fast torching and a high level of control of the ame during the application of the membrane.
These membrane is generally used as vapour barrier and, in some cases, as under layer in multiple layers water- proofing solution. It shall be applied fully bonded with a suitable propane torch.
swissporBIKUPLAN TNT 5.0
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references.
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie
www.rilco.ie
TECHNICAL DATA SHEET swissporBIKUPLAN TNT 5.0
swissporBIKUPLAN TNT 5.0 is a high quality SBS modi ed membrane reinforced with a TNT (Tissue Non Tissue) polyester stabilized with longitudinal glass yarns. The upper face of the membrane is nished with talc that renders it compatible with several glues and the lower face with a high quality polypropylene lms that allows a perfect control of the torching operation. The rolls have at their interior a heavy cardboard core that permit a high level of control during the application (above all of the upstands).
The membrane can be used as cap sheet under heavy protection roofs (not green roofs), whether they are insu- lated or not, especially those which are subjected to high levels of stress or in cold climates or as underlayer in multiple layers waterproo ng solutions. It shall be applied fully bonded with a suitable propane torch.
swissporBIKUPLAN TNT MINERAL 5.0 (Black)
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references.
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie
www.rilco.ie
TECHNICAL DATA SHEET swissporBIKUPLAN TNT MINERAL 5.0 (Black)
swisporBIKUPLAN TNT Mineral 5.0 (Black) is a high quality SBS modi ed membrane reinforced with a TNT (Tissue Non Tissue) polyester stabilized with longitudinal glass yarns. The upper face of the membrane is nished with black slate that render it UV resistants. The under face is nished with a high quality polypropylene lm that per- mits a very fast torching. The rolls have at their interior a heavy cardboard core that allows a high level of control during the application of the membrane (above all of the upstands).
These membranes are generally used as cap sheets on various roof types, whether they are insulated on not. They shall be applied fully bonded with a suitable propane torch.
swissporBITUMEN PRIMER VS 102
Use: It is very important that the concrete surfaces to be treated are as dry as possible, clean and free from oils and chalking powders. The product is ready to use, to be applied by brush, broom, roll or spray.
In polymer-bitumen membranes hot ame application, is highly recommended to use the product only if concrete surfaces are perfectly dry; alternatively a bituminous primer speci c for wet surfaces is suggested.
The drying time depends on the concrete‘s porosity, on lm thickness and on both surface and environmental temperatures. The lm usually dries within 1 hour from application at a temperature of 23°C and relative humidity of 50%. Should the primer thickness be very high, the temperature be rigorous or substructure be not much absorbent, this time could be longer, up to 2-4 hours.
The approximately consumption of swisspor BITUMEN PRIMER VS102 is 150 g/m2. To clean the tools use common synthetic or nitrous diluents.
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references. Application:
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie
www.rilco.ie
TECHNICAL DATA SHEET swissporBITUMEN PRIMER VS 102
Bituminous primer with oxidized bitumen and pure solvents. The product has main advantages: good adhering and penetrating properties when applied, quick drying lm, absence of stickiness.
swisspor Bitumen PRIMER VS102 TL is used as undercoat to block the effects of dust and minimize concrete surfaces porosity, allowing a quick spreading and application of polymer-bitumen membranes, in both hot ame application and cold application with bituminous glues. It is also used as waterproo ng coating on concrete’s walls, as xing primer on cement, wood and metal surfaces, and as protective lm for tubes and metal tanks.
swissporBIKUPONTE PRIMER
Use: It is very important that the concrete surfaces to be treated are as dry as possible, clean and free from oils and chalking powders. swissporBIKUPONTE PRIMER is ready to use, to be applied by brush, broom, roll or spray. In polymer-bitumen membranes hot ame application, it is highly recommended to use the product only if concrete surfaces are perfectly dry; should they be wet, it is advisable to use a speci c primer. Drying time depends on the concrete porosity, on lm thickness and on both surface and environmental temperatures. The lm usually dries within 1 hour from application; should the primer thickness be very high, the temperature be rigorous or the substructure be not much absorbent, this time could be longer, up to 2-4 hours.
The approximately consumption of swissporBIKUPONTE PRIMER is 100-250 g/m2 according to the surface porosity. Clean the tools with common synthetic or nitrous diluents.
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references. Application:
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
RILCO Roofing & Cladding
The Slate Cottage
Nuttstown
Clonee
Dublin 15
Tel: 00 353 (0)1 801 5690
info@rilco.ie
www.rilco.ie
TECHNICAL DATA SHEET swissporBIKUPONTE PRIMER
Bituminous solution based on oxidized bitumen and technical solvents. The product grants good adhesion and penetration to the support, preventing surface stickiness. After the application, it forms a quick drying lm.
swissporBIKUPONTE PRIMER is used as undercoat to block the effects of dust and minimize concrete surfaces porosity, allowing a quick spreading and hot ame application of polymer-bitumen membranes.
swissporBIKUTOP Sun Reflect
Use: Mix carefully before use. The product shall only be applied with environmental temperatures between + 5° C and + 35° C and when no fog, rain nor freeze are forecasted, avoiding extreme hot and cold weather conditions even when the product is still drying. Before applying it, make sure that the surfaces to be treated are clean, free from dust, chalking powders, incoherent parts, rust, disarming oils and any kind of coating. To avoid water stagnation, which could damage the lm, it is advisable that the support is inclined of at least 3%.
Apply at least two layers of the product, better if crossed, in order to guarantee color uniformity, insulating and re ective power ef cacy. Average consumption of swissporBIKUTOP Sun Re ect shall be 0,30 – 0,50 kg/m2 on standard p.b. membranes; 0,50 – 0,70 kg/m2 on slated p.b. membranes. These values may vary according to the support porosity and the desired thickness. Apply the rst layer (by brush, broom, roller or spray) after diluting the product up to 10%-15% with water; the second layer can be applied undiluted or with a slight dilution of 5% and shall be applied only over the lm of the rst layer, once it is perfectly dried up and after at least 12 hours from the rst application. Application over freshly laid bituminous surfaces shall be avoided, since they could release hydrocarbons and cause adherence problems of the lm to the membrane. Average drying time on just dried up surfaces: 6 months on membranes or other hot glued bituminous products; 3 months on cold glued bituminous products; 24 hours between the rst coat and the second one. swissporBIKUTOP Sun Re ect shall not be step over, exception made in case of maintenance. Do not expose the packing at temperatures below + 5° C; once frozen, the product is no longer usable. Clean the tools with water after use. Should the product have dried on the tools, use hot water to remove it.
Safety: Material Safety Data Sheets are available upon request at the under mentioned mail address of the Team Export.
Storage: The material has to be stored in a dry covered place and it is advisable not to exceed 12 months of storage and rolls must be stored vertically on pallets or on flat surfaces. Protect the membrane from extremely low temperatures and stabilize the material before its installation, leaving it at least 24 hours in a room at +5°C. During storage avoid exposure to direct sunlight.
Application: For a correct use of the products, refer to the specific technical documents issued by swisspor Romandie SA anyway the customer is responsible for ensuring that each product is suitable for its intended purpose and that the condition of use are suitable. If any law, norm or regulation different from what declared by the manu- facturer is in force in the Country where the product must be installed, this must be considered as compulsory by the applicator and it is his own responsibility to follow the suitable legislative references. Application:
Disclaimer: swisspor Romandie SA pursues a policy of constant product development and information contained in this document that is therefore subject to change without notice.
TECHNICAL DATA SHEET swissporBIKUTOP Sun Reflect
Flexible and elastoplastic liquid white paint in water emulsion with decorative and protective purposes. Once dried out, swissporBIKUTOP Sun Re ect forms a strong and exible lm, which perfectly adheres to the support. The product has a high resistance against atmospheric agents and prevents the dried lm from cracking. swissporBIKUTOP Sun Re ect creates a highly re ective shield against UV rays, granting not only an excellent thermal insulation, but also a considerable energy saving.
swissporBIKUTOP Sun Re ect is used to protect bitumen-polymer membranes and especially to reduce tempera- ture absorption and increase diffused light, thus improving the ef ciency of photovoltaic panels. The product may be applied on concrete, ber cement, wood and metal surfaces.